DCC concepts

Roller Gauge Trackmaking tools for Finer looking OO/HO track using OO-FB standards. 1mm flangeways will look great but are designed for finer wheel back to back spacing so RTR will need adjusting! Made for use with with code 100 flat-bottom rail (1.2mm flangeways)! Two roller gauges per pack, with convenient handles also supplied.

More DCCconcepts products

Roller Gauge Trackmaking tools for Finer looking OO/HO track using OO-FB standards. 1mm flangeways will look great but are designed for finer wheel back to back spacing so RTR will need adjusting! Made for use with with code 70/75/83 flat-bottom rail (1.1mm flangeways)! Two roller gauges per pack, with convenient handles also supplied.

More DCCconcepts products

Roller gauge N 9 mm - DCC concepts
Trackmaking tools for N scale code 80/55. Two roller gauges per pack, with convenient handles also supplied.

More DCCconcepts products

3 point track gauge OO/HO 16.5 mm - DCC concepts
Creating accurate UK prototype rails is made much easier with copper clad sleepers. They only have copper where needed for rail or chair fixing. Designed for 4mm scale / 16,5mm gauge and HO.

More DCCconcepts products

HO-Gauge Rolling Road Premium Edition – 10 Axle - DCC concepts
The HO Gauge Rolling Road is designed to be very easy to use and exceptionally reliable. We use only high quality materials so you can expect many years of trouble-free use.

Installation and use.
The Rolling Roads work equally well with DC or DCC power.

• As delivered, your Rolling Road is ready to use on 16.5mm gauge OO/HO or similar track. Also included spacers for UK prototype fine scale gauges.


• For two rail track power use, place the Gold plated roller sets onto the track at an appropriate spacing. The rollers will pick up power directly from the track so you can now place your loco onto the rollers.


• For 3-rail track power use for Hornby Dublo, Trix Twin or Märklin AC locos, two 3-rail adapters are included. They are fixed to the blue spacers which have been pre-made to accept them using the screws provided. Leave the screws slightly loose to you can easily adjust roller spacings. Once screwed in place, the alligator clip fixed to the centre-pickup plate should be attached to the centre power rail of your 3-rail track.

• Please use the screwdriver that we have provided with your DCCconcepts Rolling Road as the correctly sized magnetised tip makes this much easier for you.


• Slip the gold end caps off & replace the 16,5mm spacers with those for EM or P4, then carefully replace the screws. (Do not over-tighten the screws).

• Keep the track area that will be used with your rolling road clean so that it can transfer the power reliably.


• Clean as needed. Please do not use abrasive cleaners.


• The stainless-steel roller-bearings are pre-lubricated but you can of course add a little fine oil if you wish.

O-Gauge Rolling Road Premium Edition – 6 Axle - DCC concepts

The DCC concepts O Gauge Rolling Road is easy to use and reliable.

Installation and use.
The Rolling Road works well with AC, DC & DCC.
To make adjusting spacing easier every roller contains a strong Neodymium magnet to allow easy adjustment and to hold it in place.

To give the magnets something to work with "magnetic plates" are included in the set. They are etched to represent wooden planks so the can be installed on your layout. Secure these with silicone or contact-type adhesive in an appropriate position on top of the sleepers and between the rails.

Once the plates are secured, place the Roller sets over them at an appropriate spacings and connect the track power. The Roller sets will collect power directly from the rails so you are now ready to go.

Place your locomotive on top of the Roller sets and control it as if it was on the track. It will operate in place allowing examination for service, careful adjustment of decoder set-up or running in of a new Loco.

Service and Maintenance

Keep the track area that will be used with your rolling road clean so that it can transfer the power reliably.
DCCconcepts Roller sets have been gold plated, so they will never tarnish and always conduct power reliably. (Please – do not use abrasive cleaners. A quick wipe with alcohol or similar is all that will ever be needed)
The stainless-steel roller-bearings are pre-lubricated but you can of course add a little fine oil if you wish.


Manual (pdf)


More DCC concepts products

Change the direction of a turnout via SPDT switches.

Power: 6 - 12V or 12 - 18V DC. Average power 20mA.
Connection: 9 way spring terminals.

Dimensions:
Body only: 28mm x 38 mm x 52mm deep.
Top overall incl. fulcrum and tabs: 40mm x 45mm.
Depth incl soldering-free connectors: 68 mm.

Manual

More DCCconcepts products

Change the direction of a turnout via DCC or with momentary momentary switches.

Power: 9 - 23v DCC or DC. Static <5mA, active average <40mA.
Connection: 9 way spring terminals.

Dimensions:
Body only: 28mm x 38 mm x 52mm deep.
Top overall incl. fulcrum and tabs: 40mm x 45mm.
Depth incl soldering-free connectors: 68 mm.

Manual

More DCCconcepts products

Change the direction of a turnout with SPDT switches.

Power: 7 - 23V DC. Static <5mA, active average <40mA.
Connection: 9 way spring terminals.

Dimensions:
Body only: 28mm x 38 mm x 52mm deep.
Top overall incl. fulcrum and tabs: 40mm x 45mm.
Depth incl soldering-free connectors: 68 mm.

Manual

More DCCconcepts products

Cobalt-SS 2 Pack – Small, Reliable, Super-Smooth Above-Board Turnout Motors, ready for DC or DCC use.

Cobalt-SS 2 Pack – This pack contains 2x Cobalt-SS Above-Board Point Motors with “Plug & Play” leads to connect to the Control Board. They are ready for installation and connection with everything needed already in the pack. Cobalt-SS can be powered by either DC or DCC systems. Operation is possible by DCC, conventional switches or both.
Contents of the pack
- 2 Cobalt-SS motors
- 1 control board
- Linkages and screws
- Y-connect and reverse lead
- Extension lead

Manual

More DCCconcepts products

Cobalt-SS Universal extension leads with reverse connection option.
Length: 1000mm
Use these cables to control your Cobalt-SS motors in pairs, either both moving in the same direction, or moving opposite each other.

More DCCconcepts products