tools and more

12 magnets with pouches and about 30 screws to assist magnet mounting.




More DCC concepts products

a selection of 30 small magnets.




More DCC concepts products

4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a 3 way point to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for asymmetric 3 way point (pdf)

More DCCconcepts products

4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of Diamonds to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.

template for 5 and 6 crossing (pdf)
template for 7 and 8 crossing (pdf)

More DCCconcepts products

4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for double slip 7 and 8 (pdf)

More DCCconcepts products

4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow any point between B9 and B6 and A5 to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
The thickness of these sleepers is 1.6mm and they vary in length.

template for A5 turnout (pdf)
template for B6 turnout (pdf)
template for B7 turnout (pdf)
template for B8 turnout (pdf)
template for B9 turnout (pdf)

More DCCconcepts products

4mm scale UK prototype Pointwork sleepering, pre-etched. This fret contains enough correct length sleepers to allow a selection of slips to be constructed. Tie Bars included. Sleepers are 1.6mm thick for direct soldered construction. Designed for 4mm scale / 16,5mm gauge and OO-SF.
template for outside slip (pdf)


More DCCconcepts products

33m Kapton tape 5mm - DCC concepts

Kapton is extremely thin but also very hard, and makes the perfect insulation tape for installations needing good insulation without bulk.


More DCCconcepts products

Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.

The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.

It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.

LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.

One-year warranty.


More DCC concepts products

3 pack - Intelligent inductive detector - Legacy Models
The detector works on all layouts powered with every DCC brand or scale and every computer control IO input that can sense a high/low detection.

The detector will detect anything that alters the electrical state in a section. Examples are powered items such as Locomotives, illuminated coaches or rolling stock with resistive wheelsets. Even just a single tail lamp or a lamp in a Guards van or Caboose.

It is simple to install: It needs no soldering or complex set-up. It can be added later or at the time of layout creation. Just create a gap in one rail covering the area you wish to detect and pass the dropper wire which goes from the track power bus to that rail through the hole in the LM-iD coil. No other set-up or fiddling to do. It is that simple.

LM-iD is very easy to connect: every output uses screw terminals and it is possible to easily add an external panel LED and directly connect to and operate both low voltage logic-level things and higher current items such as relays.

One-year warranty.


More DCC concepts products

4 baseboard alignment dowels with powerpoint- DCC concepts

These dowels are fitted with power bus conntion.

2 pairs of precision baseboard alignment dowels. Easy to install for accurate joining of baseboards.
Tools needed are: a pilot drill and a 13mm and 19mm spade bit.
2 pairs is enough to make two joints (Joins three baseboards together).

More DCCconcepts products